My Power Woodworking Tools

I was recently asked about my set of power woodworking tools and thought it best to deliver the answer in a post.


My intention, when I set out on this journey, was to be free to create the things I needed / wanted … from small wooden accessories to furniture and even structures. Though I haven’t blog much about it (I hope to catch up with that story in the future) I have done what I set out to do. However I have experienced certain limitations that I think are as valuable to acknowledge as the tools I have chosen to work with.

The greatest challenge, and most of my time in the workshop, is spent on converting raw construction grade pine wood into workable pieces. This is an unpleasant task with power tools because it is noisy and very dusty. I believe that with hand-tools this experience can be very different … maybe even more pleasant, but maybe also more time-consuming. However I don’t have any experience with alternative hand-tools … except to say that good hand tools are as expensive as good power tools. This work also depends greatly on the quality and state of the wood I am working with. I have some air-dried (over a few years) wood left over in my attic which behaves very differently then the current green wood I am using to build a new outside roof and deck.

I consider the results I am able to achieve to be mediocre. The tools that I have do not enable me to achieve for reliable, consistent sizes. This effects my entire process of design and construction. I have learned to work within these limitations. I both enjoy the limitations and simplicity that this requires of me AND look forward to having better tools that will enable me to produce better quality materials and projects.

As you will see I chose to go with Bosch professional tools. When I did my initial survey my impression was that they had better build quality than Makita tools and similar quality to Dewalt (which are harder to find here). I consider this a long term investment and so opted to go with Bosch professional tools (blue products) and not the home tools (green products). Ideally I would have liked to go with Festool – I believe they are superior in quality but this also reflects in their prices.

A mitre saw (GCM 12 SD) is a very versatile tool but is often first in line for cutting long board to length. I chose this model for its large cutting capacity (effected by the blade size and sliding rails). A sale in the UK and a friend that helped in getting it shipped to Romania in an affordable way made it possible for me to enjoy this saw … otherwise I would have probably opted or a smaller size:


Next in line is a circular saw (GKS 55 CE) which I use for both cross-cuts (simple cuts on long boards that are difficult to get on the mitre saw) and length-cuts. The main choice to make here are the size of the blade and the strength of the motor. Sometimes I wish I had a larger blade, but I chose to go with this size thinking that on a construction site it is lighter to carry / lift / hold in less then ideal positions.


The next tool is the planer (GHO 26-82). The numbers reflect two dimensions – the maximum depth of cut (2.6mm) and the cut width (82mm). I rarely use a depth of cut deeper then 1.5. The larger the cutting width the stronger an engine is needed. I use it to convert the raw surface into something more pleasant, workable that can accept finishing more effectively. I use this tool a lot and I was wrongly expecting it to provide better results. I have not been able to use this tool to brings board to a predetermined size … I try to use it efficiently and make use of the resulting sizes as effectively as possible. This is not a substitute for a jointer and a fixed planer (where the tool is stationary and the wood is moved) or a combination planer-thicknesser (which is high on my wishlist).


The results of the planer depend on the qualities of the wood and my proficiency in using it. Regardless, after planing there will be sanding to do … and plenty of it. The orbital sander (GEX 150 AC). I decided to go with only one sander (because of costs) hence the orbital sander which can be used for both rough and fine sanding. Because of the limitations of the planer I spend a lot of time sanding. I think the sanderis the machine with the most working hours in the workshop.


The combined work of the planer and sander takes, by my estimate, 10 times (or more) time then it would to run the same piece of wood into a planer-thicknesser and the results (no matter how much care and efforts I put into the work) are lesser. I don’t enjoy this preparation phase and it is a demotivating part of the work that sometimes keeps (or delays) me from starting a project. This effect is magnified by the poor-to-mediocre quality of wood I have access to.

For smaller, more subtle, shaped cuts I use a jigsaw (GST 150 BCE):


… and a router (GOF 900 CE) is a very diverse tool, but is more complicated, takes more learning and experimentation to get to know and harness:


Though I rarely use it for wood-working an angle grinder (GWS 8-125) has been a priceless addition to this set. I didn’t initially get one and didn’t intend to. However I soon needed it and have since used it many times. It’s engine doesn’t run much, but it too is a diverse tool and when it does run it does precious work.

Despite their limitations I have been able to create almost everything I have wanted to create with these tools. The results are not particularly refined however I value more a freedom to design and shape things to be exactly the way I want them, to fit into the exact spaces I have available and to cater to the functions I intend them to do.

There are many more tools that serve me in the workshop … but these are the major wood-working related power tools.


Leave a Reply